Iflawyer
Ask a Lawyer
…
← All guidesΒ·Verification8 min read2026-10-13
Quality control inspection plan for a Chinese supplier

Your Quality Control Plan with a Chinese Supplier: AQL, First-Article and In-Process Inspection

AQL sampling, first-article inspection, DUPRO and pre-shipment checks β€” the inspection schedule that catches defects before the container leaves the port.

You cannot inspect every unit in a 20,000-piece order, so quality control in China is a sampling-and-scheduling discipline: decide how many units to check, at which production stage to check them, and what defect rate is acceptable. The pieces have standard names β€” AQL, first-article inspection, DUPRO, pre-shipment inspection β€” and once you understand them, a QC plan becomes a template you reuse on every order rather than a panic response to the last one.

AQL: the sampling standard behind every report

Acceptance Quality Limit (AQL) sampling rests on two equivalent systems: ISO 2859-1:1999 and ANSI/ASQ Z1.4-2003 (R2018). The AQL value you pick β€” commonly 0.65, 1.0, 1.5, 2.5 or 4.0 β€” expresses the worst acceptable average percentage of defective units. A tighter value means a larger sample and a stricter call. The same standard defines inspection levels: General Inspection Level II is the default, Level I draws roughly half the sample, Level III roughly double, and the Special levels S-1 to S-4 are reserved for destructive, costly or slow tests. In plain terms, agree the AQL value and the level with the inspector in writing, because they decide how much gets opened and what 'pass' means.

First-article inspection (also called IPC)

The first checkpoint happens at the very start of production, once materials are in and the first units come off the line β€” typically at up to about 20% completion. The point is to catch a wrong material, a wrong colour or a wrong process before the whole run commits to it. One terminology note helps when talking to inspectors: in consumer-goods inspection this stage is usually called an Initial Production Check (IPC), while 'First Article Inspection (FAI)' is the term more common in manufacturing and aerospace contexts such as AS9102. The two names describe the same early gate, so use whichever your inspection company uses and do not be thrown when the report title differs.

DUPRO: the mid-run correction point

During-production inspection (DUPRO) runs at roughly 20% to 80% completion. By now the line is running at real speed, which is exactly what you want to observe β€” real workers, real tools, real packaging β€” and the inspection lets you correct a defect trend with most of the order still unmade. DUPRO is the cheapest place to fix a problem, because the alternative is discovering it at 100% completion when everything must be reworked or rejected.

Pre-shipment inspection: the release decision

Pre-shipment inspection (PSI, also called final random inspection or FRI) happens at 80% to 100% completion, with the goods already packed, and is the gate that decides whether the container ships. The inspector draws the sample per the agreed AQL and level, checks appearance, function, quantity, labelling and packaging against your spec, and issues a pass, a fail, or a conditional pass with corrective actions. For most buyers this is the non-negotiable final gate: no PSI pass, no balance payment.

What a third-party inspection costs

  • Typical China market range: roughly USD 200–400 per inspector-day, plus travel for remote factories.
  • Independent local inspectors: often around USD 150–250 per day.
  • Branded firms such as SGS, TÜV or Bureau Veritas: commonly USD 280–400 per day.
  • Platform-priced services such as QIMA: higher list prices β€” around USD 419 per day for a product inspection and around USD 669 for a supplier audit, travel included.

Treat any single figure as an estimate and get a quote for your factory's location and your product's complexity before budgeting. The inspection fee is small next to the cost of the rework it prevents.

πŸ’‘ Write the plan into the purchase order

Put the schedule in the contract: IPC at start-up, DUPRO around mid-production, PSI before balance payment, at an agreed AQL (for example 1.5 for major defects) and General Inspection Level II. A supplier that resists a specified inspection schedule is telling you something about the run before it begins.

A working QC plan is three inspections at three moments, tied to a stated AQL, paid for by the buyer and written into the order. It does not guarantee zero defects β€” no sampling plan does β€” but it guarantees that defects are found while you can still do something about them. This content is general information and not legal or engineering advice; confirm sampling standards and current inspection prices with the relevant providers.

This guide is general information for overseas buyers and is not legal advice. For a specific transaction or dispute, consult a qualified lawyer licensed in the relevant jurisdiction.

Verify a supplier now

Run due diligence on a Chinese supplier before you pay.

Verify now
βš–οΈLawyerπŸ€–AI Expertβœ‰οΈEmailinfo@iflawyer.com